EFIE and PWM Wiring Diagram for HHO Systems
by admin on Tuesday, March 10th, 2009 | 25 Comments
If your a newbie (like me) and dont really know what goes where when it comes to wiring, check out this vid, it might help. AH Oh yea here are some links that have some good INFO & articles about EFIE and PWM stuff. http://www.internationalhydroxy.com/articles/general-information/efie-electronic-fuel-injection-enhancer-described.html http://www.fuelsaver-mpg.com/documents.html http://hhohuntsville.com/Hho_electronics.html http://www.internationalhydroxy.com/articles/general-information/efie …
Duration : 0:9:30
[youtube dJxjUjXRcR0]
Use 10 ga wire if …
Use 10 ga wire if you plan to operate your cell at 30 amps. Also the longer length of the wire will create more resistance and heat which could be a fire hazard. I recommend a constant current PWM instead of the motor control PWM you have.
DO NOT go to …
DO NOT go to PWMPOWER for your E.F.I.E.
He may rip you off as he did to me.
When you order over the net, you pay and hope to get what you paid for.
I ordered BOTH an E.F.I.E. and a PWM, and got NOTHING!! from PWMPOWER!!
Be Warned!!!
Nice video! Well …
Nice video! Well done! But whats that music in the background. Sorry I found it distracting otherwise good work.
Muchas GRACIAS!!!,,
Muchas GRACIAS!!!,,
What about …
What about controlling the frequency of the PWM?
exactly what i …
exactly what i needed.THANKS!!!
Find out what PMW …
Find out what PMW is and how to connect it to you HHO gen.
Don’t use salt use baking soda salt makes Chlorine.
HHO gas floats up to the ceiling in a house do project outside.
Use wind power while driving down the road the wind resistance
against the car and a wind turbine connected to the HHO cell.
Search for “simple generator” on YouTube.
Hello, I want to …
o, I want to contact you for more information, can you give me your email.
Please contact me
Thx
nice work, wat kind …
nice work, wat kind of frequency range do we want the PWM to be able to handle??
Nice job. As the …
Nice job. As the owner of an electronics company that invents/improves HHO products, I always stress to my customers this EXACT method of connecting the hydrogen generator to a vehicle. It is VITAL that you connect your switch (that controls the relay) to a “switched” 12 volt circuit. This switch MUST only be active when the engine is running. Otherwise you run the risk of explosion and possible suffocation. Great information on this video!
autozone has them, …
autozone has them, if you still cant find them give me an e-mail and i can get them for you and mail em to youi
you’re n smart …
you’re n smart man, awesome info
Hi Steve great …
Hi Steve great stuff mate keep it up, you can get a resettable 20 or 30 amp fuse that will reset themselves, most auto shops should have them – autocheap in AUS has them so you guys should find them over in USA.
Very cool well done …
Very cool well done and to the point I am starting a project with my son on this subject and your vidio was very helpful. We still have more research to do but you cleared up a lot of questions we had in language we can understand. Mel
you only need 2…. …
you only need 2…. (the bank 1)
the other 2 (bank 2) are in ralation with the cat. doesnt take any control with the A/F realation..
thank you very much …
thank you very much for the explanation I’m from the Dominican Republic and wanted an explanation to better understand the system take care thank you very much and God bless you
Thanks for the …
Thanks for the compliment, but I am just trying stuff and finding what works. As for new vids, just go to my profile page and look at the more recent vids.
Peace
Congratulations …
Congratulations Almosthydrogen !!! Very interesting an clear material, and honest presentation.
Please, point me to your latest cell work to learn a little more.
Tks,
From Chile
I’m not smart on …
I’m not smart on all that stuff, but from what I have read on different hho sites, you need one efie for each sensor.
Again check with others to see if this is the case.
yea I’m looking at …
yea I’m looking at a heavy duty pwm – as for the efie & stuff, not sure if I need that yet. Well see as testing goes on.
thanks for the tips.
i have a 1999 ford …
i have a 1999 ford van with (4) 02 sensors. what efie do i need for their control? 4.2 engine
Hi Steve, Nice …
Hi Steve, Nice video, however I think you might want to put a fan on that control box that’s housing the PWM. They get hot and can burn out. EFIE on the O2 circuit is probably not a good way to go with OBDII. My research is leading me to believe that EFIE is best used to modify the MAP and/or the MAF signals. Modifying the O2 signal voltage could allow the fuel system to lean out so much that the cat will burn up.
Keeping im mind Gas is still the primary fuel we burn and it must burn properly.
(sigh) your not …
(sigh) your not paying attention (again).
Read my comment very slowly & very carefully because I said…
“Personally I am looking for a heavy duty pwm, something in the range of 80 amps max and about 60-65 amps continuous.”
“LOOKING FOR…” not ‘MAKING’.
No where did I say I was going to MAKE anything; & it still doesnt make ur over priced pwms any better; and until you do some comparison testing, all your doing is talking trash, & I dont have time for that.
Stop talking trash …
Stop talking trash & listen real good cause I am only going to say this once… I’ve never owned an efie or have I promoted any product (except JB Weld & Marine Epoxy).
If u read the description box it says “here are some links that have some good INFO about EFIE and PWM stuff”. In the vid I state they have good INFO & articles; never said to purchase anything or that I endorse them.
So before u start swearing more u better reconsider; ur so close to getting banned, its not even funny.
The links you gave …
The links you gave for those efie units are way too expensive.. My units are $50 each, the ones your promoting are over 80 bucks each and one is over 100 bucks!.. Wtf??